Minicom Advanced Systems Minicom Supervisor Phantom Przewodnik Instalacji

International HQ Jerusalem, Israel Tel: + 972 2 535 9666 [email protected] North American HQ Linden, New Jersey Tel: + 1 908 4862100 info.usa@minic

PHANTOM MX IP 11. The MX IP rear panel ports The figure below illustrates the ports on the MX IP. www.minicom.comPOWER85-265VAC 50/60 HzCOMPUTERSYSTE

INSTALLATION GUIDE 12. 13. Pre-installation instructions • Switch off all computers, and disconnect the power cords • Place cables away from fluore

PHANTOM MX IP 4. You can connect a local KVM console to the User ports of the MX IP and work locally on the Phantom system. Figure 11 illustrates the

INSTALLATION GUIDE 16. Connecting the MX IP system The MX IP system is connected using Shielded CAT5 FTP System cable. The Shielded CAT5 FTP System c

PHANTOM MX IP SYSTEM INSYSTEM OUTPhantomSpecterOUTIN Figure 12 The Phantom Specter ports 19. Connecting the Specter II PS/2 Connect the Specter as i

INSTALLATION GUIDE 21. The RS232 power options 1. USB connection for power only – see Figure 14. To System Out port ofprevious unitTo System IN port

PHANTOM MX IP 23. Connecting the Specter USB Connect the Specter as illustrated in the figure below. Connect the Specter to a computer with the built

INSTALLATION GUIDE 25. Controlling the RS232 Specters You can control the RS232 Specters from the Telnet window of the Phantom MX IP when the system

PHANTOM MX IP RS232TerminalMX IPVT420Contra st Bri g htdigi talLogin: adminPassword_|SDP110To Serialport 3www.minicom.comPOWER85-265VAC 50/60 HzCOMPUT

INSTALLATION GUIDE Note! IPMI V1.5 is only supported by server systems manufactured in 2002 onwards. 28. Connecting the Internal Reset/Power Option

PHANTOM MX IP Table of Contents 1. Welcome ...

PHANTOM MX IP 29. 30. 31. 32. Connecting the External Reset/Power Option Refer to the of the External Power Switch Option guide to connect this to on

INSTALLATION GUIDE 33. Connecting the RS232 Serial cable To operate the Phantom system with the Control software located on the Marketing & Docum

PHANTOM MX IP Appendix A: Pin assignments RJ 45 Connector Ethernet 18 Pin Assignment Pin Assignment 1 TX + 5 Not connected 2 TX - 6 RX - 3

INSTALLATION GUIDE RS232 Serial cable pin-out RJ11 Service Signal DB9 1 N/C - 2 TXD 2 3 RXD 3 4 N/C - 5 GND 5 6 N/C -

PHANTOM MX IP Appendix B: Technical specifications Host computer - Operating systems DOS, Novel, Linux, UNIX, Windows 3.1,9X, ME, NT4, 2000, XP, 200

INSTALLATION GUIDE Operating temperature 5°C to 40°C / 41° to 104°F Storage temperature -40°C to 70°C / -40° to 158°F Operating humidity 10% to 90%

PHANTOM MX IP 25 PHANTOM MX IP 25

INSTALLATION GUIDE 1. Welcome The Phantom MX IP system is produced by Minicom Advanced Systems Limited. Technical precautions This equipment generate

PHANTOM MX IP 2. 3. 4. Introduction The MX IP system from Minicom is a CAT5 based Distributed KVM Switching system with remote KVM access via IP. You

INSTALLATION GUIDE Figure 1 Phantom MX IP Figure 2 Phantom UPM 5. Remote units The Remote units are external boxes called Specters. Each remote com

PHANTOM MX IP Figure 5 The Phantom Specter II RS232 Figure 6 The Phantom Specter II USB 6. 7. Compatibility The system is compatible with: • IBM c

INSTALLATION GUIDE MX IP automatically detects the current video mode of the console, however manual tuning is recommended to get the best video quali

PHANTOM MX IP 3 in 1 CPUcableTo last Specter’sSystem Out portShielded CAT5FTP cablesTo first Specter’sSystem In portwww.minicom.comUSER COMPUTERSERVIC

INSTALLATION GUIDE IPMI Version 1.5 - defines a serial connection to access certain system parameters and perform system actions like powering down or